Litter Robot Globe Position Fault (2024)

1. Litter-Robot 4: Red light bar with partial white flashing (Globe position)

  • If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle. You ...

  • Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.

2. Litter-Robot 3: All three lights flashing (Globe position fault)

  • The Litter-Robot 3 is equipped three LED lights to indicate certain statuses and faults with your unit. If all three of these lights are flashing in one of ...

  • Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!

3. Litter Robot 3 Home Position Fault - RobotShop Community

4. Litter Robot III - Home positioning fault - RobotShop Community

  • 22 apr 2024 · Recently our Litter Robot III LR3C-1200-CE (SN LR3CI359573) shows a home position fault. The globe stops at the end of the cycle just before ...

  • Recently our Litter Robot III LR3C-1200-CE (SN LR3CI359573) shows a home position fault. The globe stops at the end of the cycle just before it returns to its home position. Suggestions I found on the web didn’t help. It is using the official adapter and it is directly plugged in the wall socket. Up till now I just turn off the robot, reposition the globe by hand and turn it on again. It will cycle and will work for a while as expected until it doesn’t. Rinse and repeat. I don’t think the motor ...

5. Litter-Robot 3 Support, Troubleshooting, and Solutions

  • Litter-Robot 3: All three lights flashing (Globe position fault) · Litter-Robot 3: Blue light flashing (Drawer full indicator "DFI") · Litter-Robot 3: Buttons ...

  • Have questions about your Litter-Robot 3? Get quick solutions from our dedicated support page. Start troubleshooting now.

6. Litter-Robot 4 Support, Troubleshooting, and Solutions

  • ... (Globe position) · Litter-Robot 4: Red ping-pong light bar (Motion in drawer) · Litter-Robot 4: Red with partial yellow flashing (Over-torque fault) · Litter- ...

  • Need assistance with your Litter-Robot 4? Find guides & troubleshooting tips. Get the support you need today.

7. Litter-Robot 3: Fixing the globe magnets

  • ... globe gear track to monitor the position of the globe. The magnets could be missing or put in backward, reversing the required polarity. (Globe magnet). If ...

  • Troubleshooting your disassembled Litter-Robot 3 Globe? Our guide helps you check magnet positions and correct errors for a smoothly functioning unit.

8. Litter Robot Troubleshooting: Fixing Common Litter-Robot 3 Issues

  • 25 apr 2016 · If it cannot cycle after three attempts, the globe will return to the home position, and the control panel will flash yellow and red or blue and ...

  • Need help with your Litter Robot 3 issues? These are the most common problems and step-by-step ways to fix them.

9. Litter-Robot 3: Pinch contact installation guide

  • Follow the steps in our Litter-Robot 3: All three lights flashing (Globe position fault) guide to inspect the position sensor. If your unit is still not ...

  • Find easy steps on replacing the pinch detect terminals of your Litter-Robot 3. Visit now for a quick and smooth fix to enhance your product's efficiency.

10. Litter-Robot 4: Light codes guide

  • If your unit's light bar is red with two flashing white lights, this indicates that the unit cannot detect the Globe position. Learn more. Red with flashing ...

  • Discover solutions for all Litter-Robot 4 light codes in our comprehensive guide. Find quick fixes and get your Litter-Robot working perfectly again. Click now!

Litter Robot Globe Position Fault (2024)


How do you fix a Litter-Robot cat sensor fault? ›

Check for obstructions that might prevent the cat sensor from functioning.
  1. Make sure Litter-Robot is on a firm, level surface.
  2. The cat sensor function can be affected if the unit is on carpeting or a litter mat.
  3. Check that there are no power cords running underneath the base of the robot that might obstruct movement.

What is the dump position fault on a Litter-Robot? ›

There are three different light combinations that are related to the position of the globe. Blue, then yellow, then red (Flashing sequentially, one light at a time): This means the unit cannot find the dump position. It will continue to function in automatic mode but needs repair.

How to clean Litter-Robot sensor? ›

Vacuum the inside perimeter of the bezel with a brush attachment, passing over the holes at the top of the bezel where the curtain sensors are located. Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a Clean cycle.

What happens if you put too much litter in Litter-Robot? ›

If there is too much litter in the globe, it can cause cycling issues (getting stuck during a cycle).

Can a Litter-Robot be repaired? ›

Yes, we offer repair services. If your unit needs repair, contact our Customer Experience Team to discuss what the options are.

Why is my Litter-Robot globe not rotating? ›

Confirm that the globe is positioned correctly. Visually check that the large gear that runs around the globe is sitting in the track on the base. At the back of the globe, turn the black key into the key pocket. Reassemble the bonnet and try to cycle again.

How do you replace the globe liner in a Litter-Robot? ›

Remove the old liner

Using a Phillips screwdriver, remove the bolt near the opening and the nut inside the globe. From the lip of the opening, peel back the globe liner, then unhook the liner from the slots on the left and right sides of the entryway. Slide the rubber T-mount out of the T-Slot.

What is over torque fault on Litter-Robot? ›

Using more than 10 lbs of litter can strain the motor, causing an over torque fault. Make sure the litter is just below the raised fill line. Some brands of litter are heavier than others. For these litters, we recommend keeping the litter at least a half inch below the fill line to avoid weight-related errors.

Top Articles
Latest Posts
Article information

Author: Prof. An Powlowski

Last Updated:

Views: 5974

Rating: 4.3 / 5 (44 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Prof. An Powlowski

Birthday: 1992-09-29

Address: Apt. 994 8891 Orval Hill, Brittnyburgh, AZ 41023-0398

Phone: +26417467956738

Job: District Marketing Strategist

Hobby: Embroidery, Bodybuilding, Motor sports, Amateur radio, Wood carving, Whittling, Air sports

Introduction: My name is Prof. An Powlowski, I am a charming, helpful, attractive, good, graceful, thoughtful, vast person who loves writing and wants to share my knowledge and understanding with you.